Front Right ABS Wheel Speed Sensor Replaces 47910-ZT00A 47910-ET000 for Nissan Sentra 2007-2012 | Passenger Side, 2-Pin Plug and Play

Fix the ABS light on your Sentra without a dealer visit. This front right ABS wheel speed sensor is a direct-fit replacement for the passenger-side sensor on 2007–2012 Nissan Sentra, covering both the current part number 47910-ZT00A and the earlier 47910-ET000 (Nissan lists the ZT00A as the direct replacement for the ET000). Same 2-pin connector, same mounting, same signal — no splicing, no programming.

Position: Front Right — passenger side only. The driver side uses a different part number (47911), so please do not order this sensor for the left side of the car.

Fitment: 2007–2012 Nissan Sentra with the 2.0L (MR20DE) and 2.5L (QR25DE) engines, including Base, S, SE-R and Spec V trims. Not for the rear axle and not for other Nissan models — message us your VIN and we'll double-check before you order.

Replaces These Part Numbers

Nissan OE

• 47910-ZT00A  ·  47910-ET000 (earlier number, superseded by ZT00A)

Aftermarket Cross Reference

• Standard Motor Products: ALS628
• Airtex / Wells: 5S8478 / 5S12288
• Standard: SU13706
• Other: 084-4383  ·  ABS726 (right side)

Vehicle Fitment

Fits front right only. The front left side uses 47911-ZT00A and the rear uses 47900 / 47901 — different sensors. Message us your VIN if you'd like us to confirm.

Key Features

• Direct OE replacement — factory-style 2-pin connector, plug and play
• Includes the wiring harness (the most common failure point on the original part)
• Active Hall-effect design for a clean signal at all speeds
• Sealed against road salt, mud, water and brake heat
• 100% function tested before shipping

Symptoms This Sensor Fixes

• ABS warning light staying on
• Traction control / VDC light on at the same time
• Front right wheel speed sensor fault codes
• Speedometer reading erratically or dropping out
• ABS kicking in at low speed, or failing to engage when it should

Installation (about 45 minutes)

1. Loosen the lug nuts, raise and support the front of the car, remove the wheel.
2. Unplug the sensor connector and remove the mounting bolt.
3. Pull the old sensor out and clean the mounting hole and hub surface.
4. Install the new sensor, routing the harness exactly like the original.
5. Reconnect, refit the wheel, torque the lug nuts to factory spec.
6. Drive a short distance — the ABS light should clear on its own.

Tip: on higher-mileage cars the old sensor can be seized with rust. Soak the bolt in penetrating oil first, and clean rust off the tone ring while you're in there to avoid false ABS trips.

Warranty

1-year limited warranty against manufacturing defects. Contact us for a replacement if the sensor fails within the warranty period.

FAQ

Is this for the left or the right side?
Right — the passenger side. The driver side uses a different part number (47911), so this sensor will not fit the left side.

My old sensor says 47910-ET000 — is this the same part?
Yes. 47910-ZT00A is Nissan's updated number for 47910-ET000; they are the same sensor and fully interchangeable.

Will it fit my 2013 or newer Sentra?
No — this sensor covers the 2007–2012 Sentra. Message us your VIN with the model year and we'll confirm the right part.

Do I need a scan tool after installing?
No. The ABS module re-learns the signal on the next drive. If the light stays on, clear the stored codes with a scanner.

Why did my original sensor fail?
Almost always corrosion at the sensor tip or a broken wire in the harness — which is why this replacement includes the full harness.